![]() ![]() Motherboards with VIA VT2021 Gigabyte GA-Z77X-UD3H-WB WiFi Gigabyte GA-Z77-D3H Gigabyte GA-Z77M-D3H Gigabyte. I have spent a good couple of days working on a solution to get everything working on my GA-Z77-D3H build. Unlike some ASUS boards you cannot run more than 1 fan on the CPU fan header without a splitter.ĪSUS' Q-connector thing is gimmicky, but it would save time (about 5 minutes) if they included something similar. So as we know the VIA VT2021 is on a couple of new Gigabyte Ivy Bridge Boards. Your 4th fan is full speed, fans 1-3 are all linked together in RPM ramp up. This means it is spotty outside of Windows.įan control is rudimentary due to the SuperIO. If you prefer the black PCB board, there is Z77X-D3H for you which is 20USD more expensive. The VIA VL800 controls four extra USB ports on the back of the board, and these don't work without drivers. Ds3h z77 hackintosh build My hackintosh build: Gigabyte GA-ZDS3H, Intel I5 K, Sapphire Radeon HD OC Boost Vapor-X 3GB GDDR5, Dell PQ, Audio. VIA audio is not fully supported for Hackintosh builds (, ), although in my testing it works fine on Linux variants (Debian based and Fedora) No ripple at all and a lower average voltage than the ASUS P8P77-V Pro." - Anandtech > "The response of the Gigabyte board under load is fantastic. ![]() Run VoodooHDA.If you're an overclocker and don't want spend $180+, this is your boardĢ oz copper PCB (something missing on the Z77X-D3H, note lack of U), Glass fabric PCB relevant for LN2 OCsīIOS allows control of voltages and timingsīIOS / Software doesn't lie: I tested with a multimeter and the voltage is within 0.001 of what's on the BIOS screenīest OC board under $150 : V-check points, POST code display, Power button, good VRM that doesn't use D-PAK mosfets, Dual BIOS Run VoodooHDA.prefPane to install it under System Preferences Reboot the Machine and everything should be working Starting Windows and other OSes is done by Clover's way. It started as Clover using Clover's GUI and ability to change settings and then started OpenCore to inject and patche kexts and start macOS. Place VoodooHDA.kext and AppleHDADisabler.kext on the Desktop Since rev5123 devs make joined bootloader Clover+OpenCore. All inputs and output work on my Lion 10.7.4 build.ĭownload AppleHDADisabler.kext - ĭownload VoodooHDA.prefPane. Manual Processor: Intel Core i7 3770K, Graphics: Integrated Intel HD4000 Wifi/BT: Fenvi FV-T919 (Broadcom BCM94360CD) Current version is OpenCore 0.5. I tried VoodooHDA all the versions from 2.6 and up to the latest 2.7.3 with no luck i would always get a Kernal Panic when booting and having the sound card enabled.Īnyways here is the solution i have in place. Hackintosh-OpenCore-GA-Z77X-UD5H-3770K-HD4000 OpenCore EFI folder and support files for the following hardware: Motherboard: Gigabyte GA-Z77X-UD5H, rev. ![]() I have spent a good couple of days working on a solution to get everything working on my GA-Z77-D3H build.Īfter pulling my hair out so many, many times i almost admitted defeat and got an external USB sound card as everyone was saying you had to get. on my Gigabyte-based Hackintosh that is built around a GA-Z77X-UP5 TH motherboard. So as we know the VIA VT2021 is on a couple of new Gigabyte Ivy Bridge Boards. My main considerations with this build are: Working Optical Audio (I connect to a Sony AV Receiver) Working HD4000 Graphics alongside GTX660TI (For video encoding/decoding performance + Airplay) Networking that doesn't crash on large file transfers (I have a NAS. MOJAVE Gigabyte H97M-D3H (MATX/H97) - Clover ONLY installation method. Building a CustoMac Hackintosh: Buyer's Guide ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |